 |
|
The PIRANHA KLUTCH from KARATA is the solution for high-horsepower and big-inch engines used
in today’s radical custom bikes. KARATA'S PIRANHA KLUTCH chews up all other clutches. Featuring 1.000" more clutch stack height and more friction material than any other clutch on the market, PIRANHA is designed for Karata's 4.000" and 5.000" Intimidator®Series Belt Drives. KARATA'S PIRANHA KLUTCH will handle any of the big engines on the market, bar none. Even stock bikes and mild customs can benefit from the state-of-the-art PIRANHA KLUTCH design which delivers, smooth, consistent shifts every time. Two versions are available, the massive 26-plate PIRANHA and the tough 16-plate PIRANHA JR. For bikes with engines over 120-cubic inches, with or without turbos, superchargers or nitrous, the severe-duty PIRANHA is the ultimate clutch that bites back against slippage and delivers every
horsepower straight into the ground. The PIRANHA JR. is recommended for motorcycles with engines smaller than 120-inches in any trim from ultra-high performance to the flash cruiser. Even STOCK MOTORCYCLES that accept 1990-1997 clutches are able to run the PIRANHA JR.
| |
| Piranha Klutch for 4 & 5" Intimidator Belt Drives | | Piranha | 89003 |
 | |
| Big Twin OEM clutch replacement and all Intimidator Series Primary Belt Drives | | Piranha Jr. | 89001 |
|
|
| |
|
Both versions share KARATA’S high-tolerance machining, a billet steel hub, Kevlar clutch plates that
can be run wet or dry and dedicated steels. All PIRANHA KLUTCHES feature a polished billet aluminum
pressure plate and are fully tuneable with KARATA’S proprietary clutch spring kits.
Installation, and service are made easy by PIRANHA’S brutally-strong yet simple design. As with all
KARATA products, all individual components that make up both PIRANHA KLUTCHES are available
separately to allow for maintenance and service over a lifetime of use.
With one of the largest clutch packs in the industry, the PIRANHA was tested on a 195-cubic inch monster Big Twin engine with no failures! With a billet steel hub, hard-anodized aluminum center section and fully replaceable steel spring studs, the PIRANHA and PIRANHA JR.
KLUTCHES provide back-up like no other. Holeshot after holeshot, KARATA’S PIRANHA KLUTCHES dig in every time.
ALL Complete Piranha Klutches include the following:- Billet Aluminum Pressure Head with knurled Steel Insert and adjustment screw & nut
- Steel Locator Hub, 30-tooth
- Complete Klutch Pack [13 kevlar/ 13 steel -Piranha, 8 Kevlar / 8 steel -Jr.]
- 18 springs [6 each - gold 60 lbs, green 85 lbs. & red 100 lbs.]
- Inner Klutch Hub
- Heavy Duty Snap Ring
Piranha Replacement Parts
| 89015 |
|
PIRANHA JR. |
KLUTCH PACK-COMPLETE |
| 89016 |
|
PIRANHA |
KLUTCH PACK-COMPLETE |
| 89025 |
|
ALL |
INNER KLUTCH HUB |
| 89026 |
|
PIRANHA JR. |
30 TOOTH INNER STEEL LOCATOR HUB |
| 89027 |
|
PIRANHA |
30 TOOTH INNER STEEL LOCATOR HUB |
| 89028 |
|
ALL |
PRESSURE PLATE |
| 89031 |
|
PIRANHA JR. |
STUD PACK 6 |
| 89032 |
|
PIRANHA |
STUD PACK 6 |
| 89034 |
|
ALL |
SPRING RETAINER 6 |
| 89036 |
|
ALL |
SPRING RETAINER BOLTS 6 |
| 89038 |
|
PIRANHA JR. |
CLUTCH ADJUSTMENT SCREW AND NUT |
| 89040 |
|
PIRANHA |
CLUTCH ADJUSTMENT SCREW AND NUT |
| 89042 |
|
ALL |
HEAVY DUTY SNAP RING |
| 89050 |
|
ALL |
KLUTCH SPRINGS GOLD 60 LBS. 6 |
| 89052 |
|
ALL |
KLUTCH SPRINGS GREEN 85 LBS. 6 |
| 89054 |
|
ALL |
KLUTCH SPRINGS RED 100 LBS. 6 |
| | |
|
 |
Karata Enterprises Co
3 River Road
Conshohocken, PA 19428
Phone 610-825-2070
Fax 610-941-6142
[email protected]
|
 |
|
|
| |
| |
